Home > Brake Light > Chevy Truck Brakes Lights Not Working

Chevy Truck Brakes Lights Not Working


WV Ridge Runner - 05 Impala LS - 03 Black Silverado 2500HD 4X4 LB CC LT - 93 S-10 4X4 Blazer (Tahoe LT) - 79 Monte Carlo - Harleys, 4-Wheelers, etc... Unhook connector latch and carefully pull out. Forgot your Password? We're trying to get it to work so if I get this job we can have two vehicles. this contact form

Then the problem came back again. Credentials confirmed by a Fortune 500 verification firm. If thats not the issue, i will use your suggestions.....Thanks for the reply. 3 out of 3 people think this is helpful. Thanks for the help. https://www.cargurus.com/Cars/Discussion-t27831_ds530776

2003 Chevy Silverado Brake Lights Not Working

I think on most C/K 1500/2500 it is on the brake pedal arm or the arm hits it. Get a volt meter and put set it for DC volts to test all wires at the steering column. still have no brake lights. Labeled (hazard stop) It was blown, Even with the fuse blown the hazards still worked.??

Hell, i didnt until a friend of mine showed me aboit 4 years ago. just need to remove a clip and lift up on the plastic piece to remove it from the brake cable, then disconnect the wiring harness and pop in the new one, ok, how did you do that Ask Your Own Chevy Question Share this conversation Related Chevy Questions Question Date Submitted Have new 5.7 reman engine from power train products and new Chevy Silverado Brake Light Problems EmailReport underoath1064 Senior Member Posts: 180 Loc: pleasanton texas Reg: 01-19-05 User InfoSend Private TopicView Profile Re: Brake lights don't work 05-17-05 08:48 AM - Post#694899 In response to

Run the wire to the white side of the brake pedal connector and see if you have brakes. Gmc Sierra Brake Lights Not Working I have not seen the issue the OP had but something is causing the circuit to draw to much current and I would suggest checking the connections on the brake light Try the hand brake (or however you call the brake that you use while parking the car).


Category:Chevy Share this conversation Expert: Randall C replied3 years ago. 2006 Chevy Silverado Brake Lights Not Working Was this answer helpful? Do you need the fuse box diagram/layout?JACUSTOMER-dlst591n- : Im n I t sure how to read tbe diagram you sent and im looking ay the fuse layout diagram but can't find I assumed the relay labeled "brake" in the box was for the lamps.

Gmc Sierra Brake Lights Not Working

You will pop the airbag and it will hurt you. http://www.gmtruckclub.com/forum/threads/brake-lights-not-working.118981/ Originally Posted by TheStereoGuy I work with automotive electronics for the last 12 years. 2003 Chevy Silverado Brake Lights Not Working Reply With Quote 11-03-2011,11:56 PM #16 TheStereoGuy View Profile View Forum Posts View Blog Entries View Articles My Hattiesburg Resident Achievements: Join Date Nov 2007 Location Laurel/Hattiesburg Posts 8,033 Hub Bucks Brake Lights Dont Work But Tail Lights Do Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading...

I put in a new switch and all was well for 3 months. http://clearduplicatefiles.com/brake-light/chevy-suburban-brake-lights-not-working.html Y'all have scoped out the fuses good and I am sure they have all been checked... Get a couple of midgets with red flashlights and just yell brake and they'll turn their flashlights on. Yes No Voted Undo Score 59 Cancel Comments: 1992 GMC CK3500 7.4 454. 2004 Chevy Silverado Brake Lights Not Working

Watch Queue Queue __count__/__total__ Find out whyClose Chevy Trailblazer- No Brake Lights! Yes No Voted Undo Score 0 Cancel Comments: Would your fix be the same on a 95 silverado brake light on cab works fine? Can you tell me or will tell me how you came to possess this knowledge? http://clearduplicatefiles.com/brake-light/car-brakes-lights-not-working.html CarGurus | My account Saved searches Saved listings Saved promotions Sign in Join | Advertise | United States Canada United Kingdom Used Cars New Cars Car Values Sell My Car

Thanks 14 out of 14 people think this is helpful. Brake Light Wiring Diagram Chevy Turn Signal works and I change the turn signal switch and brake switch. We(him) have already checked most of the connections in the process of changing all this garbage trying to fix it.

Runs best on HiVelocity Hosting.Copyright 2004-2014 MyHattiesburg.com Login|Contact Us Chevy Chevrolet Repair Questions?

April 12 by Bo Gus Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Try these out and we will go from there... Three bulbs: they just pull out but won't want to come easy. 1997 Chevy Silverado Tail Lights Not Working There's a fuse.

I changed the switch just now and they won't come on at all. Add to Want to watch this again later? Reply With Quote 11-02-2011,05:56 PM #6 Fish-Bait View Profile View Forum Posts View Blog Entries View Articles MH ass in the hole Achievements: Awards: Join Date Feb 2007 Posts 59,041 Hub his comment is here Do you have a trailer hitch installed?

Find the fusebox and look for "brake". Was this answer helpful? Yes im in correctRandall : this is odd, if you are 100% you have the correct fuse, you should have power all the time on one terminal. If you do have power going to the switch check to see if you have power leaving the switch when depressed, if not, it is the switch.

EmailReport 66C10 Senior Member Posts: 141 Age: 47 Loc: Contra Costa County, CA Reg: 10-30-04 User InfoSend Private TopicView Profile Re: Brake lights don't work 07-26-05 03:24 PM - Post#694902 I did notice when my blinker is on (headlights turned off)when I hit my break my dash lights for my "heat and cool" flash with my blinker. I have been fighting a taillight issue for 2 days. Hope it helps someone else out there.

They run through wire shroud from front to back along the inside of the frame to the left tail light. beltstowing 61,960 views 26:24 2004 chevy Avalenche REAR break job - PART1 - Duration: 14:21. I can 11/12/2016 11/12/2016 almind3 08 Tahoe drivers door windows, locks, mirror and seat heater 11/12/2016 11/12/2016 ggrote1 Is it still safe to drive my, Oops. Removed each terminal by releasing the clip in the harness connector, then used a probe to push the binder strip to a tighter position.

The time now is 12:00 AM.