Home > Christmas Light > Christmas Lights Not Working After Storage

Christmas Lights Not Working After Storage

Contents

After taking down the lights, plug them in before storing them, to make sure they still work. Also be aware that most holiday light bulbs have short life expectancies, about 1,000 to 1,500 hours. reversing the plug would allow the dc to light up the other side of the string. Found one with a broken wire, inserted a small piece of wire into the hole where it should have been as a bridge, and popped it back into the socket. this contact form

It is not light reading especially when you are preparing dinner, decorating the tree, and trying to watch Frosty The Snowman... it does happen every year but not this much so I guess I'm especially frustrated. Cancel Mark Makarenko Rep: 1 Posted: 11/28/2013 Options Permalink History the same thing happened to me. LED #7 proved to be the problem. http://www.popularmechanics.com/home/how-to/a3231/how-to-fix-a-string-of-christmas-lights-14774047/

How To Fix Christmas Lights Half Out

They do have a "Threshold" that once exceeded will fail, then that whole string will be out. Even a small current can be dangerous if it goes through a human chest. Triacs work. NOBODY seems to know the reason for this , and everybody seems to experience it .

Cancel Danny Rep: 1 Posted: 01/01/2014 Options Permalink History Question : I have a string of lights that will only come on if it is warmer than minus 15 degrees Celcius I discovered it before I put it up on the eaves. When we find that condition, we can replace the bulb, or re-seat it, or possibly replace the socket. How To Test Christmas Lights Without A Tester Current limiting resistors are usually too small, letting too much current flow, particularly when used in a warm climate.

Yes No Voted Undo Score 57 Cancel Comments: ok I have a set of Holiday Time Icicle LED outdoor lights,now my problem is that half way thru the first set about Read the manual very carefully and as always, proceed with caution. CONNECT END TO END A MAXIMUM OF THREE (3) LIGHTING STRINGS OR DECORATIVE OUTFITS OF THE SAME TYPE," and that is the answer. 100-bulb light strings typically use "3A" fuses. Repeat until you find a bulb with current on one side of it and no current on the other.

In any case, you can remove and test a bulb using the LightKeeper Pro or a multimeter. How To Fix Christmas Lights Without A Tester Christmas extension cords also often have these fused protections so check your extension cord as well. • A bulb which has burned out and whose shunt has failed to take over I pushed the prongs into position, put the LED in the socket, and the rest of the strand came to life. This sharing pattern continues for every subsequent bulb which burns out.

How To Replace Christmas Light Bulb

As to the fix you mentioned, if there are that many disposed light strings, could you not cut that light out and replace it with a salvaged one. http://ths.gardenweb.com/discussions/2298539/christmas-lights-half-on-half-off-why In order for your LEDs to wok on that circuit they need half of those oscillations to be eliminated. How To Fix Christmas Lights Half Out A fuse can also blow when the wires are accidentally stapled during installation, or when the lights are plugged into a socket with too high a voltage (such as US lights How To Find The Bad Bulb On Christmas Lights But it is important to realize that typically three similar-looking wires are wrapped together between sockets.

I only have a small tree, not pre-lit either - so when I have problems with a strand of lights, it gets tossed. weblink The recyclers, for the responsible, are getting filled up with these strings of lights, and the Landfills for the less responsible . On that note, my string uses two 3 amp fuses in the plug which both test less than one ohm and there are three wires connected to the spades which are So 'screw it', off to the landfill they go ! How To Find Broken Light In Christmas Lights

Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Checking the Fuse on Christmas Lights Before trying out some of the more detailed fixes, check the fuse for the lights. If you read on the box, you're only supposed to use so many strings per extension cord, but I don't remember how many. navigate here And to do it right the cost will be prohibitive, unless some big changes are made.

If there was a problem with one of those sub-sets, just that set would not light. How To Fix Christmas Tree Lights Half Out Write a guide Explore more guides View previous 8 Ways to Troubleshoot Your LED Christmas Lights Image 8 Ways to Troubleshoot Your LED Christmas Lights Published by: eBay How to Troubleshoot While some may think that an issue with a string of Christmas tree lights means they can no longer use them, many times they can fix the problem on their own.

Twist this over the wire, holding it in place.

Sometimes it is just the fuse too. We all want to be responsible with our things—no one wants to just rush out and buy something new when we can fix the old—but if you aren't already armed with Undo blizlady As Alex said, ".....my methods of dealing with those sweet little non-working light strands usually result in statements truly inappropriate for the season.... :)" My thoughts exactly...lol!! Parallel Christmas Lights Was this answer helpful?

This means that the energy can't go past that piece of metal, which results in everything burning out. It is much, much better to buy two strings to operate one string, and then use the other simply for replacement bulbs. Proper storage is key to their continued success. his comment is here you have three choices.

A Homemade Dimmer This past year we bought a very cheap string with a "snowball" diffusing coating that started blowing 4 or 5 bulbs a week. and buy a tube of dielectric grease. Yes No Not Helpful 3 Helpful 1 Unanswered Questions I have a string of lights with five dead lights in the middle but the rest work fine. and don't buy a noma pre-lit tree.

Most strings come with a couple of replacement bulbs which may be enough for a few weeks of operation. It is so frustrating, I know. Turn the connector several times until the cap feels secure, and you can tug on it without it falling off. It may seem tedious, but it is actually straight forward and simple to do.

These ‘Money saving’ LED lights , aren’t , because one keeps having to buy new strings every year ! Fixing a string of lights isn't always that simple.