Home > Not Working > Catalina Spa Jets Not Working

Catalina Spa Jets Not Working

Contents

Sign in 11 Loading... Ralph I asked for help and even though u felt it should be left to a professional, thank u for ur response. If one has an air pocket, then the pump can be started and stopped several times in a row (by pushing jet button) in order to try to clear the air Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Source

Back to Top SE or STANDARD ECONOMY Message The Spa is Operating in the "Standard in Economy" (SE) Heating Mode. It’s important to know when it’s necessary to call on a licensed repair-man, or when you can make a simple repair and save yourself a bundle. This turns on pump 1, and also turns on the circ pump. - Verify that both pump 1 and the circ pump are running and that water is flowing out of If not, you may have to use the drain plug or keep reading.

Hot Tub Jets Not Working On One Side

A gasket or o-ring inside the pump union keeps the water from leaking out, so no additional silicone, glue or teflon tape etc. Won't light up won't turn on won't do anything. Too Many Closed Jets. To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes.

Weather Tempature got below freezing. I filled the tub up with new water and went to check on it a few hours later an no power at all. There could be a few things preventing your jets from pumping water. Hot Tub Jets Weak It has high and low speed.

Just enough to let some water or air out. Half Of Hot Tub Jets Not Working Back to Top SAH or SANITIZER HIGH Message At the ORP Sensor, the "Sanitizer Level is High" (SAH). Here is a list of some common hot tub issues and solutions. 1. Each union and drain plug represents a spot in the equipment where we can bleed the air from.

Published on May 8, 2012Every so often, air can get stuck and stop your pump from working properly. In Ground Spa Jets Not Working If they're not, or you're not sure that both are (because you can't tell whether you have two separate flows at different rates or just one flow), momentarily turn both pumps If the SnS or Sn Message is Blinking or Flashing OFF and ON without showing Water Temperature, it is a Verified Sensors Out of Sync Message. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or Continue for a Detailed Test Procedure.

Half Of Hot Tub Jets Not Working

The System will stay in the Standard Mode for 1 Hour unless the "Mode/Prog" Button is Pressed on a Panel with a "Mode/Prog" Button, or the "Temp" Followed by "Light" Buttons https://aqua-tech.ca/support-posts/the-pump-on-my-hot-tub-works-but-the-jets-dont-turn-on/ Under the plate would be the cartridge filter that may be soiled and preventing good flow. Hot Tub Jets Not Working On One Side Now tighten it up and let's do this thing for real. Hot Tub Jets Won't Turn On Janis Cuthbertson first I cleaned the filters then I replaced them still says flo Matt Giovanisci You may need to call a professional to take a look at your pump.

Take the filter out. With the tub off, find one that's easy to loosen. All Automatic Functions Remain OFF during this time. If there is Now a "rtC" or "RTC FAILURE" Real Time Clock Error Message, contact your Dealer or Service Organization. Hot Tub Air Lock Symptoms

Checked for continuity and power of all incoming wires and transformer. Blocked Suction Fitting. We recently drained and cleaned our Sunbelt Spa. The Real Time Clock keeps the Current Time of Day.

Check For Suction Blockage: If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below. Bathtub Jets Not Working That's your cue to start tightening. Note: The message troubleshooting shown here applies to Cal Spa control panels built in 2013 and earlier.

Closed Slice Valve.

By now u probably fixed it but I felt like answering because Matt's go to answer is call a professional. The wiring and equipment described in this article represent a typical spa pack. If the pump is coming on but not pumping water, then it has an air lock. Spa Pump Not Working Matt Giovanisci You might have air in the lines.

Your cache administrator is webmaster. Overview Awards Factory Tour Contact Us Sitemap Careers Privacy Policy Public Relations In the News Press Releases Cal Spas on TV Backyard Ideas Blog Dealer Resources Log In to Dealer Connection I heard concerns that the impellor may be damaged so it doesnt push enough for all the jets but i would expect they would atleast bubble a little rather then not If it is soiled it could also create an air lock upon fresh filling the spa.

If you haven't successfully primed both pumps by the time the Priming Mode display ( Pr or PRIMING MODE depending on panel) ends, turn off the spa IMMEDIATELY. There is Not Enough Water Flow through the Heater to carry the Heat Away from the Heating Element. If repeated attempts (hours apart) still cannot get pumps to prime, you can wait overnight and just let the spa sit. Thanks for your time.

Back to Top LF or LOW FLOW Message There is a Verified "Low Flow" (LF) Condition in the Heater. This indicates a Possible Problem with The System Board. There's no water in it, so don't go inside and make a sandwich. Tell us by commenting below!

Maybe it looks a little something like this: [attachment=0:12fija01]air relief.JPG[/attachment:12fija01] The red arrows point to unions, the blue arrow points to where there may or may not be a drain plug. If the pump is getting power, or even humming but no water is moving, there could be a problem with the impeller or other pump part, or there could be an If you have a bleed screw on top of your filter, be sure to bleed air from there too. Got it?