Home > Remote Start > Compustar Auto Start Not Working

Compustar Auto Start Not Working

Contents

When they disconnected the battery it is possible that the transponder bypass that was installed lost programming… While this is not necessarily supposed to happen, it sometimes does. Then try reprogramming the remote again. Reply Mitch Schaffer says September 3, 2012 at 7:21 pm Not sure how a couple of these comments slipped past me. I will go to the dealer and see what they say and will let you know; (just for the heck of the matter). weblink

Site Map Powered by Zendesk Home Products Support Blog Find a Dealer BY SYSTEM Remote Car Starters Security/Alarms Remote Start + Security Accessories Smartphone BY SERIES Pro Series Prime Series LT Swap out the batteries in the remote. -When your Compustar remote stops working unexpectedly or begins to work intermittently the first thing to check is battery life on the remote. Check with your installer (i’m sure you have already… Sorry).. Reply Mitch says December 6, 2012 at 7:15 pm Hard to diagnose without seeing it but I would start by checking the tach sensing wire. Get More Info

Compustar Remote Start Manual

Please help in any way you can.. Give your installer or the manufacturer a call and see what the procedure is to put it in or out of Valet mode. i Reply Mitch says January 20, 2012 at 10:35 am Chris, Wish we could help but we are not a dealer for Cool Start. Reply Mitch says January 14, 2013 at 10:56 am Hit LOCK and TRUNK at the same time for 1/2 second… I think your issue is Valet mode, not passive mode… Reply

Please visit an authorized dealer or your original installer for assistance. Reply Pauline says January 14, 2012 at 1:22 am Hi Mitch. Reply Mitch Schaffer says November 9, 2012 at 8:25 pm It might have to do with the factory security or transponder… Leaning toward the secuirty.I would call your installer. Compustar Remote Start Battery Replacement One other possibility is that your mechanic (battery replacement) severed the wire that senses the tach signal… Why not likely, it is a possibility.

The lights on the car do not go on or flash or blink we when press the auto start button. Any idea what could be wrong. They started the car remotely right after i changed the battery, but now the remote starter is no longer starting the car. Reply Mitch says February 29, 2012 at 10:25 pm Tiffany, VERY tough call..

Chantal Reply CHRIS says January 19, 2012 at 10:30 pm I have a cool start remote it has worked fine until lately i can't get it to start how do i Compustar Alarm Not Chirping Reply Pauline says January 24, 2012 at 7:34 pm No problem. Anyway, when I got the car the remote start worked one time then months later I went to use the remote start and it won't work. So i had to leave the vehicle there.

Compustar Valet Mode

Avid landscaper.... https://support.compustar.com/hc/en-us/articles/202036914-My-compustar-remotes-aren-t-working-and-I-can-t-start-my-vehicle-using-the-key-what-do-I-do- It is not a battery problem. Compustar Remote Start Manual If the indicator is red with no black bars filled in then the battery life is low on your remote. Compustar Alarm Car Wont Start Thank you.

I would have your installer reprogram it. have a peek at these guys Was rewired and works like a charm now. How do I solve this issue? If the temperature warms up however it always starts like it always did. Compustar Error Codes

See all 10 articles Mobile Application ★ How do the auxiliary functions work on my DroneMobile? The lock button flashes red on the Slice or 2W940R-SS to indicate low battery. Press the Start button, and your car should be warm and toasty! check over here Site Map Powered by Zendesk Home Products Support Blog Find a Dealer BY SYSTEM Remote Car Starters Security/Alarms Remote Start + Security Accessories Smartphone BY SERIES Pro Series Prime Series LT

P:s. Remote Start Not Working After Battery Change Regards Katherine R McCall Reply Karie Little says November 8, 2011 at 9:17 pm i get up in morning tail lights on but car not running. Reply Peter says November 26, 2012 at 2:37 pm Hello just want to see if you could tell me why my remote does start the car well actually when I hit

That's a tough one.

Reply Patricia Flynn says January 28, 2013 at 11:46 pm Hello Mitch, I was hoping you could help me as I have been calling the dealer, leaving several messages over the but then it will run the starter again and grind. It could also be a bypass programming issue. Compustar Remote Start Installation Manual Error 8- Engine/Tach sensing My vehicle remote starts, but then immediately shuts off.

If you have been back to the installer several times, ask them to provide you with the results of the current draw tests. The next step is to attempt to reprogram the remote to the vehicle. Reply Mitch says February 13, 2012 at 4:22 pm Victor, You may have a bad transmitter or antenna. this content Thanks.

Reply Anonymous says January 27, 2012 at 6:33 pm Ok great thanks Mitch Reply Chris says January 27, 2012 at 12:50 am An Xtreme EX-2300 TW was installed on my Toyota What I was doing wrong was holding LOCK and TRUNK at the same time until the lights flickered on the remote. Please go to the shop where you had it installed and they should be able to diagnose it for you. When an engine is warm it starts a little quicker and requires less crank time then when the engine is cold.

How to buy a new remote Where do I fill out the warranty registration form? Please visit our DroneMobile troubleshooting page for assistance. Yesterday I went to a store n I came out n tried to start my car with the key n it wouldn't start. I would go back to the shop that installed it and asked them to take a look.

Or what needs to be done on my car to make the remote start work? How do I disable my Compustar alarm when my remote is not working? It started. What should I do when I sell a vehicle with a DroneMobile unit in it?

How do I find the model number of my DroneMobile unit?